View SY88913VKG_754400.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Micrel, Inc.
5V/3.3V 1.25Gbps HIGH-SPEED LIMITING POST AMPLIFIER
SY88913V
SY88913V
FEATURES
s s s s s s s s s s s 3.3V and 5V power supply options Up to 1.5Gbps operation Low power Low noise Chatter-Free /LOS Generation PECL /LOS Output TTL /EN Input Differential PECL inputs for data /EN input is TTL with internal 27K pull up Single power supply Designed for use with Micrel-Synergy laser diode driver and controller s Available in a tiny 10-pin (3mm) MSOP
DESCRIPTION
The SY88913V limiting post amplifier with its high gain and wide bandwidth is ideal for use as a post amplifier in fiber-optic receivers with data rates up to 1.5Gbps. Signals as small as 5mVp-p can be amplified to drive devices with PECL inputs. The SY88913V generates a chatter-free PECL Loss of Signal (/LOS) output. The SY88913V incorporates a programmble level detect function to identify when the input signal has been lost. This information can be fed back to the /EN input of the device to maintain stability under loss of signal conditions. Using LOSLVL pin the sensitivity of the level detect can be adjusted. The LOSLVL voltage can be set by connecting a resistor divider between VCC and VREF, Figure 2. Figure 3 and 4 show the relationship between input level sensitivity and the voltage set on LOSLVL.
APPLICATIONS
s s s s 1.25Gbps Gigabit Ethernet 531Mbps and 1062Mbps Fibre Channel 622Mbps SONET Gigabit Interface Converter
BLOCK DIAGRAM
DIN
Limiting Amplifer ECL Buffer
DOUT /DOUT /EN
/DIN VREF
Enable
VCC GND
Level Detect
LOSLVL
LOS
M9999-081505 hbwhelp@micrel.com or (408) 955-1690
Rev.: C
Amendment: /0
1
Issue Date: August 2005
Micrel, Inc.
SY88913V
PACKAGE/ORDERING INFORMATION
Ordering Information
/EN 1 DIN 2 /DIN 3 VREF 4 LOSLVL 5 MSOP K10-1 10 VCC 9 DOUT 8 /DOUT 7 6 /LOS GND
Part Number SY88913VKC SY88913VKCTR(1) SY88913VKG SY88913VKGTR(1)
Package Type K10-1 K10-1 K10-1 K10-1
Operating Range Commercial Commercial Industrial Industrial
Package Marking 913V 913V 913V with Pb-Free bar-line indicator 913V with Pb-Free bar-line indicator
Lead Finish Sn-Pb Sn-Pb Pb-Free NiPdAu Pb-Free NiPdAu
16-Pin MSOP (K10-1)
Note: 1. Tape and Reel.
PIN NAMES
Pin DIN /DIN LOSLVL /EN /LOS GND DOUT /DOUT VCC VREF Type Data Input Data Input Input TTL Input PECL Output Ground PECL Output PECL Output Power Supply Output Function Data Input Inverting Data Input Loss of Signal Level Set Output Enable (active Low) Loss of Signal Indicator (active Low) Ground Data Output Inverting Data Output Positive Power Supply Reference Voltage Output for LOS Level Set (see Fig. 2)
GENERAL DESCRIPTION
General The SY88913V is an integrated limiting amplifier intended for high-frequency fiber-optic applications. The circuit connects to typical transimpedance amplifiers found within a fiber-optics link. The linear signal output from a transimpedance amplifier can contain significant amounts of noise, and may vary in amplitude over time. The SY88913V limiting amplifier quantizes the signal and outputs a voltage-limited waveform. The TTL /EN pin allows the user to disable the signal without removing the input signal.
M9999-081505 hbwhelp@micrel.com or (408) 955-1690
2
Micrel, Inc.
SY88913V
ABSOLUTE MAXIMUM RATINGS(1)
Symbol VCC DIN, /DIN DOUT, /DOUT, /LOS LOSLVL VREF TA Tstore Rating Power Supply Voltage Input Voltage Output Voltage (with 50 load) Input Voltage Output Voltage Operating Temperature Range Storage Temperature Range Value 0 to +7.0 0 to VCC VCC -2.5 to VCC +0.3 0 to VCC VCC -2.0 to VCC -40 to +85 -55 to +125 Unit V V V V V C C
Note: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
VCC = +3.3V 10% or +5V 10%, RLOAD = 50 to VCC -2V
TA = -40C Symbol ICC IIL IIH VCMR Voffset LOSLVL VOH VOL VREF VIH VIL Parameter Power Supply Current(1) 5V 3.3V Min. -- -- -0.3(5) -- -- Max. 35 35 -- 20(2) 100(3) 100 VCC TA = 0C Min. -- -- -0.3(5) -- -- Max. 35 35 -- 20(2) 100(3) 100 VCC Min. -- -- -0.3(5) -- -- TA = +25C Typ. 21 23 -- -- -- -- 40 -- Max. 35 35 -- 20(2) 100(3) 100 VCC TA = +85C Min. -- -- -0.3(5) -- -- Max. 40 40 -- 20(2) 100(3) 100 VCC
VCC -880
Unit mA mA A V mV V mV mV V V V
/EN Input LOW Current /EN Input HIGH Current Common Mode Range Differential Output Offset LOSLVL Level DOUT and /DOUT HIGH Output DOUT and /DOUT LOW Output Reference Supply(4) /EN Input HIGH Voltage /EN Input LOW Voltage
GND +2.0 VCC -1.0 GND +2.0 VCC -1.0 GND +2.0 -- VREF -- VREF -- VREF
VCC -1.0 GND +2.0 VCC -1.0 -- VREF
VCC -1085 VCC -880 VCC -1025 VCC -880 VCC -1025 VCC -955 VCC -880 VCC -1025
VCC -1830 VCC -1555 VCC -1810 VCC -1620 VCC -1810 VCC -1705 VCC -1620 VCC -1810 VCC -1620 VCC -1.38 VCC -1.26 VCC -1.38 VCC -1.26 VCC -1.38 VCC -1.32 VCC -1.26 VCC -1.38 VCC -1.26
2.0 --
-- 0.8
2.0 --
-- 0.8
2.0 --
-- --
-- 0.8
2.0 --
-- 0.8
Notes: 1. No Output Load. 2. VIN = 2.7V. 3. VIN = VCC. 4. IREF must be limited to be within -0.8mA (source) and 0.5mA (sink). 5. VIN = 0.5V.
M9999-081505 hbwhelp@micrel.com or (408) 955-1690
3
Micrel, Inc.
SY88913V
AC ELECTRICAL CHARACTERISTICS
VCC = +3.3V 10% or +5V 10%, RLOAD = 50 to VCC -2V.
TA = -40C Symbol PSRR VID VOD tOFFL tONL tOFFH VSR HYS tr, tf Parameter Power Rejection Ratio Supply(1) Min. -- 5 -- 200 -- -- -- 5 2 -- -- Max. -- 1800 -- -- 0.5 0.5 0.5 50 8 260 -- TA = 0C Min. -- 5 -- 200 -- -- -- 5 2 -- -- Max. -- 1800 -- -- 0.5 0.5 0.5 50 8 260 -- -- 5 -- 200 -- -- -- 5 2 -- -- TA = +25C Min. Typ. 35 -- 700 250 0.1 0.2 0.1 -- 4.6 170 trin,tfin Max. -- 1800 -- -- 0.5 0.5 0.5 50 8 260 -- TA = +85C Min. -- 5 -- 200 -- -- -- 5 2 -- -- Max. -- Unit dB Conditions Input referred, 55MHz
Input Voltage Range Differential Output Voltage Swing(2) /LOS Release Time(3) Minimum Input /LOS Assert Time(3) /LOS Release Maximum Input Time(4)
1800 mVPP -- mV -- mV 0.5 0.5 0.5 50 8 260 -- s s s mVPP dB ps
VID = 15mVPP VID = 5mVPP
/LOS Sensitivity Range /LOS Hysteresis Output Rise/Fall Time
VID > 100mVPP VID < 100mVPP
Notes: 1. Input referred noise = RMS output noise/low frequency gain. 2. Input is 622MHz square wave. 3. Input is a 200MHz square wave, tr < 300ps, 8mVPP. 4. Input is a 200MHz square wave, tr < 300ps, 1.8VPP.
M9999-081505 hbwhelp@micrel.com or (408) 955-1690
4
Micrel, Inc.
SY88913V
APPLICATION NOTE
Output Termination The SY88913V outputs must be terminated with a 50 load to VCC -2V (or Thevenin equivalent). Layout and PCB Design Since the SY88913V is a high-frequency component, performance can largely be determined by board layout and design. A common problem with high-gain amplifiers is feedback from the large swing outputs to the input via the power supply. The SY88913V ground pin should be connected to the circuit board ground. Use multiple PCB vias close to the part to connect to ground. Avoid long, inductive runs which can degrade performance.
VCC
0.1F 0.1F
DIN+
R1
DIN-
LOSLVL
50
50 VREF
R2 VREF
0.1F
Figure 1. Differential Input Configuration
Figure 2. LOSLVL Circuit Notes: LOSLVL = VCC -1.32 + R2 x 1.32 R1 + R2 R1 + R2 5k
M9999-081505 hbwhelp@micrel.com or (408) 955-1690
5
Micrel, Inc.
SY88913V
PERFORMANCE CURVE
100 90
INPUT LEVEL (mVp-p)
LOS Assert and Deassert Levels vs LOSLVL
INPUT LEVEL (mVp-p)
3.3V TA = 25C 1.25Gbps Pattern 27-1
100 90 80 70 60 50 40 30 20 10 0 0
LOS Assert and Deassert Levels vs LOSLVL
5.0V TA = 25C 1.25Gbps Pattern 27-1
80 70 60 50 40 30 20 10 0 0
-0.2 -0.4 -0.6 -0.8 -1.0 -1.2 LOSLVL = VCC - V (V)
-0.2 -0.4 -0.6 -0.8 -1.0 -1.2 LOSLVL = VCC - V (V)
Figure 3. 3.3V LOS Assert and Deassert Levels vs. LOSLVL
Figure 4. 5.0V LOS Assert and Deassert Levels vs. LOSLVL
M9999-081505 hbwhelp@micrel.com or (408) 955-1690
6
Micrel, Inc.
SY88913V
10 LEAD MSOP (K10-1)
Rev. 00
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131
TEL
USA
+ 1 (408) 944-0800
FAX
+ 1 (408) 474-1000
WEB
http://www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2005 Micrel, Incorporated. M9999-081505 hbwhelp@micrel.com or (408) 955-1690
7

▲Up To Search▲

Price & Availability of SY88913VKG

	To Download SY88913VKG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .